FAQ's about 3M Clear Bra's in MN

  • Question: Why is a Clear Bra better than other car bras or no protection?
  • Answer: The Clear Bra also known as Paint protection protects your vehicle from Rocks, insects, and debris that will significantly show wear on your cars painted surfaces within a short period of time. This is particularly true in Minnesota where they use large amounts of sand and salt on the roads. Vinyl bras catch dirt and debris between it and the hood causing scratches and discoloration. A properly installed clear bra can solve both of these problems.
  • Question: What is a 3M Ventureshield Clear Auto Bra?
  • Answer: A Clear Bra is a 8Mil urethane film with a pressure sensative adhesive. Basically its a Optically clear sticker but extremly strong. Once it is properly applied to the car's painted surface, like the leading edge of the hood, or front bumper, it is a strong protection against rocks thrown up by vehicles on the highway in winter and bug splats in summer keeping the paint underneath in perfect condition.


  • Question: Can the Clear Bra be removed if needed?
  • Answer: Yes the Clear Bra can be removed. The clear bra is designed to be removed without hurting the vehicles painted surface. From time to time the clear bra will leave adhesive on the paint. The adhesive can be cleaned off using 3M adhesive remover leaving the paint as good as the day it was installed.
  • Question: How should I take care of my new clear bra?
  • Answer: Allow several days to let the clear bra cure. After that, treat it just like it wasn't there. When using a pressure washer, you should make sure to keep the nozzle at least 36" away from the clearbra. The pressure can lift the edges or cut the film. When waxing the car, wax right over the clear bra. We recommend Plexus You may notice a buildup of wax along the upper edge of the material, and a Q-Tip works well to clean that edge.
  • Question: How long does it take to install?
  • Answer: The typical clear bra installation takes 1 1/2 hours to 3 hours.
  • Question: How long does it take to install?
  • Answer: The typical clear bra installation takes 1 1/2 hours to 3 hours. It all depends on how much coverage you are going for. A simple hood and fender tip install should take an hour or less; but a full bumper, hood, fender, rear view mirror, rocker panel area install can take several hours to complete.
  • Question: What areas of my car can be protected by the clear bra?
  • Answer: Hood: Rock chips are the most noticeabl on the front of the hood, making it the most popular part of the car to protect. The most common coverage on hoods are 12”, 18”, 24”, 30", and full hood kits.
    Front Bumper: The front of the bumper with its forward facing painted surfaces are most likely to be damaged by flying rocks.
    Side mirrors: The mirrors catch a lot of damaging stones and from time to time a garage door.
    Headlights/Foglights: Headlights are VERY expensive to replace.
    Roof & A Pillar: The leading edge of the roof and A Pillar also gets hit often by high-flying debris.
    Back bumper: The most common scratched up area of a car is its rear bumper. Putting luggage, golf clubs, groceries into the trunk are easy ways to damage your back bumper.
    Door Cups: Long fingernails, rings, or keys can scratch up the paint around door handles.
    Rocker Panels: The bottom section of the vehicle is a common area for rock and stone damage. We typically cover from wheel well to wheel well.
  • Question: Can I install a 3M VentureShield clear bra film myself?
  • Answer: The Clear Bra material is very expensive and you risk damaging the film trying to apply it yourself. Professional clear bra installers have the experience and skill required to apply the film around compound curves like headlights, bumpers and all other areas on the car.
  • Question: Can 3M VentureShield clear bra film be installed over a vehicle that has had the paint touched up?
  • Answer: All fresh paint on your vehicle will needs to be fully cured before applying 3M VentureShield paint protection film. If a clear bra film is removed, it is possible that the area around the touch-up paint could peel off. The film will protect the area until the film is removed.
  • Question: Can I cover the whole vehicle with a 3M VentureShield clear bra?
  • Answer: Prices for full vehicle clear bra installations vary. Please give us a call to discuss.
  • Question: Can 3M VentureShield clear bra film be applied over graphics and vinyl stripes?
  • Answer: es, clear bra films can be applied over vinyl graphics however, if the film is removed, damage may occur to the underlying graphic during the removal process.
  • Question: Does 3M VentureShield clear bra film resist yellowing?
  • Answer: Yellowing can occur due to UV rays affecting the material or by little dust particles getting stuck in the porous clear bra material. You can lessen the chances of your clear bra film and headlight overlays from yellowing by waxing the material whenever you wax your vehicle.
  • Question: I don’t like to see the line on the hood, can you cover the entire hood?
  • Answer: Yes, covering the whole hood is possible.
  • Question: Will my car fade under the sun?
  • Answer: Yes. 3M VentureShield film is UV stable, but will allow UV rays to penetrate. This feature eliminates the "two shades" of paint problem resulting from traditional car "bras."

Servicing the following areas:

Minneapolis MN, St. Paul MN, Rochester MN, Duluth MN, Bloomington MN, Plymouth MN, Brooklyn Park MN, St. Cloud MN, Eagan MN, Coon Rapids MN, Maple Grove MN, Eden Prairie MN, Burnsville MN, Woodbury MN, Blaine MN, Lakeville MN, Minnetonka MN, Apple Valley MN




Clear Bra Installation

Clear Bra Kits

Clear Bra Warranty

Contact Clear Bra

Clear Bra Shop (Photos)

FAQ's About Clear Bra's

Clear Bra Forums

Window Tint MN

Bravo Protection Products
15620 Wayzata Blvd.
Wayzata, MN 55391

P) 952.476.7025

Email Us

Acura Clear Bra
Audi Clear Bra
Aston Martin Clear Bra
Bentley Clear Bra
BMW Clear Bra
Cadillac Clear Bra
Chevrolet Clear Bra
Corvette Clear Bra
Chrysler Clear Bra
Dodge Clear Bra
Ferrari Clear Bra
Ford Clear Bra
GMC Clear Bra
Honda Clear Bra
Hyundai Clear Bra
Infiniti Clear Bra
Jaguar Clear Bra
Jeep Clear Bra
Kia Clear Bra
Lamborghini Clear Bra
Land Rover Clear Bra
Lexus Clear Bra
Lincoln Clear Bra
Lotus Clear Bra
Maserati Clear Bra
Mazda Clear Bra
Mercedes-Benz Clear Bra
Mercury Clear Bra
Mitsubishi Clear Bra
Nissan Clear Bra
Porsche Clear Bra
Saab Clear Bra
Subaru Clear Bra
Suzuki Clear Bra
Toyota Clear Bra
Volkswagen Clear Bra
Volvo Clear Bra





What Customers Say About The Clear Bra

"When it's your baby, Tom is the guy you want doing the install. When Tom installed the VentureShield™, he took great care to ensure the car's surface was perfectly clean, the material blemish free, and that his placement of the pre-cut material was perfect."

"A year and a half later, the VentureShield™ material has held up very well - no clouding, no discoloration, and it has taken a lot of rock hits to protect the front of my still pristine "Z." Thanks Tom."

Chris - Shakopee, MN


3M clear bra


Ventureshield Clear Bra


Xpel Clear Bra




With Clear Bra paint protection film the most vulnerable areas of your vehicle have an extra measure of protection from:

  • Chips, scratches and nicks
  • Light abrasions
  • Small road debris damage
  • Winter roads, salt and sand